[Gmsh] 3D Mesh not generated

Zenker, Dr. Matthias Matthias.Zenker at erbe-med.com
Thu Aug 15 09:51:31 CEST 2013


Hi,

I can generate and view the mesh without problems.
Is "Volume Edges" or "Volume Faces" checked under Tools->Options->Mesh->General?  Then you should see your mesh.

HTH,

Matthias


Von: Lakshmi Selvakumaran [mailto:lakshmi.selvakumaran at kaust.edu.sa]
Gesendet: Mittwoch, 14. August 2013 14:19
An: gmsh at geuz.org
Betreff: [Gmsh] 3D Mesh not generated

Hi,

I am trying to generate a simple 3D mesh of a plate of size 50 X 50 X 0.01.  I started with the 2D code of the same plate
and it works well.
When I tried to extend it to 3D using extrude command, I am unable to see the mesh eventhough my terminal says that
3D mesh has been generated.  Could you please tell me whether my code has any mistake?  Below is the code for your
reference.

Point(1) = {25, 25, 0, 1.0};
Point(2) = {-4, 25, 0, 1.0};
Point(3) = {-6, 25, 0, 1.0};
Point(4) = {-14, 25, 0, 1.0};
Point(5) = {-16, 25, 0, 1.0};
Point(6) = {-25, 25, 0, 1.0};
Point(7) = {-25, -25, 0, 1.0};
Point(8) = {-16, -25, 0, 1.0};
Point(9) = {-14, -25, 0, 1.0};
Point(10) = {-6, -25, 0, 1.0};
Point(11) = {-4, -25, 0, 1.0};
Point(12) = {25, -25, 0, 1.0};

Line(1) = {1, 2};
Line(2) = {2, 3};
Line(3) = {3, 4};
Line(4) = {4, 5};
Line(5) = {5, 6};
Line(6) = {6, 7};
Line(7) = {7, 8};
Line(8) = {8, 9};
Line(9) = {9, 10};
Line(10) = {10, 11};
Line(11) = {11, 12};
Line(12) = {12, 1};

Line Loop(5) = {1,2,3,4,5,6,7,8,9,10,11,12};
Plane Surface(60) = {5};
Physical Line(100)={1,3,5,6,7,9,11,12};
Physical Line('elec1')={2};
Physical Line('elec2')={4};
Physical Line('elec3')={8};
Physical Line('elec4')={10};

Physical Surface(200)={60};

Transfinite Line(1)=29;
Transfinite Line(2)=3;
Transfinite Line(3)=8;
Transfinite Line(4)=3;
Transfinite Line(5)=9;
Transfinite Line(6)=50;
Transfinite Line(7)=9;
Transfinite Line(8)=3;
Transfinite Line(9)=8;
Transfinite Line(10)=3;
Transfinite Line(11)=29;
Transfinite Line(12)=50;

Transfinite Surface(60)={1,6,7,12};
Recombine Surface(60);

Extrude {0,0,1.01} {Surface{60}; Layers{2}; Recombine; }

Thanks.

Best regards
Lakshmi.


________________________________
This message and its contents, including attachments are intended solely for the original recipient. If you are not the intended recipient or have received this message in error, please notify me immediately and delete this message from your computer system. Any unauthorized use or distribution is prohibited. Please consider the environment before printing this email.


_____________________________________________________________________
ERBE Elektromedizin GmbH
Firmensitz: 72072 Tuebingen
Geschaeftsfuehrer: Christian O. Erbe, Reiner Thede
Registergericht: Stuttgart HRB 380137

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.geuz.org/pipermail/gmsh/attachments/20130815/971c94f9/attachment.html>