[Gmsh] About read *.step file function？

[liang dong]

 thank you your  reply !  I only want to konw the read *.step file in gmsh source code.Somebody tell me the fuction or tell me how to find it?
                                                                               dongliang

--- 08年12月31日，周三, wing <yongjin.liu at gmail.com> 写道：

发件人: wing <yongjin.liu at gmail.com>
主题: Re: [Gmsh] About read *.step file function？
收件人: edongliang at yahoo.com
抄送: "gmsh" <gmsh at geuz.org>
日期: 2008,1231,周三,7:36上午

liang dong wrote:
> hi wing
>  Once again, thank you  so much! sorry,I donot konw the mean" gmsh
your_file_name.step
>  ' ,I want to kown the fuction read *.step file .And the mesh modle
need which information come from *.step file ? Thanks you very much!
>                                                                           
                                 liang
> --- *08年12月27日，周六, wing /<yongjin.liu at gmail.com>/*
写道：
> 
>     发件人: wing <yongjin.liu at gmail.com>
>     主题: Re: [Gmsh] About read *.step file function？
>     收件人: edongliang at yahoo.com
>     抄送: gmsh at geuz.org
>     日期: 2008,1227,周六,8:57上午
> 
>     liang dong wrote:
>     > hi：
>     > I have problem about *.step file .I want to konw how to read
*.step
>     > file in gmsh? Is "loadstep()" function? Can you tell me
where
>     the
>     > function read the *step ?I cannot find it.
>     > Thank you very much!!
>     > dongliang
>     >
>     >
>     >
------------------------------------------------------------------------
>     > 好玩贺卡等你发，邮箱贺卡全新上线！
>     >
>    
<http://cn.rd.yahoo.com/mail_cn/tagline/card/*http://card.mail.cn.yahoo.com/>
>     >
>     >
------------------------------------------------------------------------
>     >
>     > _______________________________________________
>     > gmsh mailing list
>     > gmsh at geuz.org
>     > http://www.geuz.org/mailman/listinfo/gmsh
>     >       Hi dongliang,
>     I'm not sure if there exists a loadstep() function, but when it
comes to
>     how to read *.step file in gmsh, you can try this:
>     gmsh your_file_name.step
> 
>     hope this helps.
> 
>     wing
>               
> 
> ------------------------------------------------------------------------
> 好玩贺卡等你发，邮箱贺卡全新上线！
<http://cn.rd.yahoo.com/mail_cn/tagline/card/*http://card.mail.cn.yahoo.com/>


Hi dongliang,
Seems that you are talking about the source code? I'm sorry I'm not
familiar with programming, even the source code itself, but I believe somebody
here can help if your question is described in more detail.
BTW, you should cc your mail to the mailing list <gmsh at geuz.org> so that 
everyone in the list can receive  your message.  Use  "Reply to all"
rather than  just  "Reply"  next  time.
Good luck.

wing



      ___________________________________________________________ 
  好玩贺卡等你发，邮箱贺卡全新上线！ 
http://card.mail.cn.yahoo.com/
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.geuz.org/pipermail/gmsh/attachments/20090102/6a395fa4/attachment.html>