[Gmsh] 3D Mesh not generated

Lakshmi Selvakumaran lakshmi.selvakumaran at kaust.edu.sa
Thu Aug 15 10:03:10 CEST 2013


Hi Matthias,

Thanks for your reply.  I was able to generate the mesh as well today
morning when I tried again.  But for some reason, when I save it, the mesh
file saves only the 2D mesh and not the 3D mesh.  Could you please tell me
what could be the problem?

Thanks.

Best regards
Lakshmi.




On Thu, Aug 15, 2013 at 10:51 AM, Zenker, Dr. Matthias <
Matthias.Zenker at erbe-med.com> wrote:

>  Hi,
>
>
>
> I can generate and view the mesh without problems.
>
> Is „Volume Edges“ or „Volume Faces“ checked under
> Tools->Options->Mesh->General?  Then you should see your mesh.
>
>
>
> HTH,
>
>
>
> Matthias
>
>
>
>
>
> *Von:* Lakshmi Selvakumaran [mailto:lakshmi.selvakumaran at kaust.edu.sa]
> *Gesendet:* Mittwoch, 14. August 2013 14:19
> *An:* gmsh at geuz.org
> *Betreff:* [Gmsh] 3D Mesh not generated
>
>
>
> Hi,
>
>
>
> I am trying to generate a simple 3D mesh of a plate of size 50 X 50 X
> 0.01.  I started with the 2D code of the same plate
>
> and it works well.
>
> When I tried to extend it to 3D using extrude command, I am unable to see
> the mesh eventhough my terminal says that
>
> 3D mesh has been generated.  Could you please tell me whether my code has
> any mistake?  Below is the code for your
>
> reference.
>
>
>
> Point(1) = {25, 25, 0, 1.0};
>
> Point(2) = {-4, 25, 0, 1.0};
>
> Point(3) = {-6, 25, 0, 1.0};
>
> Point(4) = {-14, 25, 0, 1.0};
>
> Point(5) = {-16, 25, 0, 1.0};
>
> Point(6) = {-25, 25, 0, 1.0};
>
> Point(7) = {-25, -25, 0, 1.0};
>
> Point(8) = {-16, -25, 0, 1.0};
>
> Point(9) = {-14, -25, 0, 1.0};
>
> Point(10) = {-6, -25, 0, 1.0};
>
> Point(11) = {-4, -25, 0, 1.0};
>
> Point(12) = {25, -25, 0, 1.0};
>
>
>
> Line(1) = {1, 2};
>
> Line(2) = {2, 3};
>
> Line(3) = {3, 4};
>
> Line(4) = {4, 5};
>
> Line(5) = {5, 6};
>
> Line(6) = {6, 7};
>
> Line(7) = {7, 8};
>
> Line(8) = {8, 9};
>
> Line(9) = {9, 10};
>
> Line(10) = {10, 11};
>
> Line(11) = {11, 12};
>
> Line(12) = {12, 1};
>
>
>
> Line Loop(5) = {1,2,3,4,5,6,7,8,9,10,11,12};
>
> Plane Surface(60) = {5};
>
> Physical Line(100)={1,3,5,6,7,9,11,12};
>
> Physical Line('elec1')={2};
>
> Physical Line('elec2')={4};
>
> Physical Line('elec3')={8};
>
> Physical Line('elec4')={10};
>
>
>
> Physical Surface(200)={60};
>
>
>
> Transfinite Line(1)=29;
>
> Transfinite Line(2)=3;
>
> Transfinite Line(3)=8;
>
> Transfinite Line(4)=3;
>
> Transfinite Line(5)=9;
>
> Transfinite Line(6)=50;
>
> Transfinite Line(7)=9;
>
> Transfinite Line(8)=3;
>
> Transfinite Line(9)=8;
>
> Transfinite Line(10)=3;
>
> Transfinite Line(11)=29;
>
> Transfinite Line(12)=50;
>
>
>
> Transfinite Surface(60)={1,6,7,12};
>
> Recombine Surface(60);
>
>
>
> Extrude {0,0,1.01} {Surface{60}; Layers{2}; Recombine; }
>
>
>
> Thanks.
>
>
>
> Best regards
>
> Lakshmi.
>
>
>
>
>  ------------------------------
>
> This message and its contents, including attachments are intended solely
> for the original recipient. If you are not the intended recipient or have
> received this message in error, please notify me immediately and delete
> this message from your computer system. Any unauthorized use or
> distribution is prohibited. Please consider the environment before printing
> this email.
>
>
> _____________________________________________________________________
> ERBE Elektromedizin GmbH
> Firmensitz: 72072 Tuebingen
> Geschaeftsfuehrer: Christian O. Erbe, Reiner Thede
> Registergericht: Stuttgart HRB 380137
>
>

-- 

------------------------------
This message and its contents, including attachments are intended solely 
for the original recipient. If you are not the intended recipient or have 
received this message in error, please notify me immediately and delete 
this message from your computer system. Any unauthorized use or 
distribution is prohibited. Please consider the environment before printing 
this email.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.geuz.org/pipermail/gmsh/attachments/20130815/59a1a73b/attachment.html>