[Gmsh] About read *.step file function？

[Robert Funnell]

Liang -

The code for reading .step files is in Geo/GModelIO_OCC.cpp.
I found it by examining Common/OpenFile.cpp and then doing
     find ./ -name \*.cpp -exec grep -H readOCCSTEP {} \;
Is that the information that you're looking for?

- Robert

On Fri, 2 Jan 2009, liang dong wrote:

>  thank you your  reply !  I only want to konw the read *.step file in gmsh source code.Somebody tell me the fuction or tell me how to find it?
>                                                                                dongliang
>
> --- 08ÿÿ12ÿÿ31ÿÿÿÿÿÿÿÿ, wing <yongjin.liu at gmail.com> ÿÿÿÿÿÿ
>
> ÿÿÿÿÿÿ: wing <yongjin.liu at gmail.com>
> ÿÿÿÿ: Re: [Gmsh] About read *.step file functionÿÿ
> ÿÿÿÿÿÿ: edongliang at yahoo.com
> ÿÿÿÿ: "gmsh" <gmsh at geuz.org>
> ÿÿÿÿ: 2008,1231,ÿÿÿÿ,7:36ÿÿÿÿ
>
> liang dong wrote:
>> hi wing
>>  Once again, thank you  so much! sorry,I donot konw the mean" gmsh
> your_file_name.step
>>  ' ,I want to kown the fuction read *.step file .And the mesh modle
> need which information come from *.step file ? Thanks you very much!
>>
>                                 liang
>> --- *08ÿÿ12ÿÿ27ÿÿÿÿÿÿÿÿ, wing /<yongjin.liu at gmail.com>/*
> ÿÿÿÿÿÿ
>>
>>     ÿÿÿÿÿÿ: wing <yongjin.liu at gmail.com>
>>     ÿÿÿÿ: Re: [Gmsh] About read *.step file functionÿÿ
>>     ÿÿÿÿÿÿ: edongliang at yahoo.com
>>     ÿÿÿÿ: gmsh at geuz.org
>>     ÿÿÿÿ: 2008,1227,ÿÿÿÿ,8:57ÿÿÿÿ
>>
>>     liang dong wrote:
>>    > hiÿÿ
>>    > I have problem about *.step file .I want to konw how to read
> *.step
>>    > file in gmsh? Is "loadstep()" function? Can you tell me
> where
>>     the
>>    > function read the *step ?I cannot find it.
>>    > Thank you very much!!
>>    > dongliang
>>    >
>>    >
>>    >
> ------------------------------------------------------------------------
>>    > ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
>>    >
>>
> <http://cn.rd.yahoo.com/mail_cn/tagline/card/*http://card.mail.cn.yahoo.com/>
>>    >
>>    >
> ------------------------------------------------------------------------
>>    >
>>    > _______________________________________________
>>    > gmsh mailing list
>>    > gmsh at geuz.org
>>    > http://www.geuz.org/mailman/listinfo/gmsh
>>    >       Hi dongliang,
>>     I'm not sure if there exists a loadstep() function, but when it
> comes to
>>     how to read *.step file in gmsh, you can try this:
>>     gmsh your_file_name.step
>>
>>     hope this helps.
>>
>>     wing
>>
>>
>> ------------------------------------------------------------------------
>> ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ
> <http://cn.rd.yahoo.com/mail_cn/tagline/card/*http://card.mail.cn.yahoo.com/>
>
>
> Hi dongliang,
> Seems that you are talking about the source code? I'm sorry I'm not
> familiar with programming, even the source code itself, but I believe somebody
> here can help if your question is described in more detail.
> BTW, you should cc your mail to the mailing list <gmsh at geuz.org> so that
> everyone in the list can receive  your message.  Use  "Reply to all"
> rather than  just  "Reply"  next  time.
> Good luck.
>
> wing
>
>
>
>      ___________________________________________________________
>  ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ 
> http://card.mail.cn.yahoo.com/